CLICKER
Universal Garage Door Opener Remote Control

The clicker remote can be programmed to operate up to 2 garage door openers or gates, including different brands. All programming is done using the:

· Brand switch

· Transmitter DIP switch

· Transmit push buttons A and B, and LED indicator

Preparation

Determine the BRAND of the existing garage door opener or handheld remote controls. If all remote controls are lost, the BRAND is located on the ceiling mounted motor unit or on the receiver near the flexible wire antenna. Proceed to the SECTION indicated on the BRAND chart below.

Note: If programming to more than one opener, after programming button "A" refer to brand chart, and follow the instructions pertaining to the brand you wish to program into button "B".

When the remotes range is diminished, operation is intermittent, or the LED dims, replace the battery. Memory is not lost when the battery is removed. Note: Dispose of old batteries properly.

clt1-img2.jpg (30638 bytes)

BRAND CHART: Proceed to appropriate section.

SECTION I    Chamberlain, Sears, LiftMaster, Master Mechanic, Dolt
SECTION II   Stanley, Multi-code, Linear, Moore-O-Matic
SECTION III  Genie

SECTION I - Chamberlain, Sears, LiftMaster, Master Mechanic, Dolt
Determine if your motor unit/receiver system has DIP switches or a smart-learn button. (Locate the small gray wire antenna. Some models require removing the light lens.)

Chamberlain, Sears, LiftMaster, Master Mechanic, Dolt Replacement Transmitter CLT-1, Clicker Brand
- If the Receiver has 9 DIP switches proceed to TYPE A
- If the Receiver has a yellow, white, or gray smart-learn button,
  proceed to TYPE B
- If the Receiver has a green, red, or orange smart-learn button,
  proceed to TYPE C
TYPE A: The Receiver DIP switch has three positions labeled "+", "0" and " - ". The "0" setting cannot be used with the clicker remote.

1) Reset switches: 1 to " - " and positions 2 through 9 to a random setting using  "+" and the " - ". DO NOT USE THE " 0" SETTING.

2) Gather any existing remotes and open to expose the DIP switches. Reset the  DIP switch to match the newly coded receiver. Note: some three button remotes do not have a #1 switch. Match the 2 through 9 to the receiver. On three button  remotes the large button is now programmed to activate the door.

3) Test all the newly coded remote controls to be sure that they operate the door before proceeding to the BRAND MODE SETTING.
TYPE B: After determining that the Receiver has a yellow, white or gray learn button:

1) Gather any existing remotes and open to expose the DIP switches labeled "+", "0" and " - ''.
 

2) Reset switches: 1 to "-" and positions 2 through 9 to a random setting using "+" and the " - ". DO NOT USE THE " 0" SETTING, SET ALL REMOTES TO THE SAME SETTING. On three button remotes the large button is now programmed to activate the door.

3) The recoded remotes must be programmed to the receiver. Press and release the smart-learn button. Then press and hold the existing remote push button for three seconds.

4) Test all the newly coded remote controls to be sure that they operate the door before proceeding to the BRAND MODE SETTING.


TYPE C: With this type receiver, the existing remotes do not contain DIP switches. Proceed to BRAND MODE SETTINGS.
BRAND MODE SETTINGS - Set switches on clicker remote
FOR TYPE A & B - Step 1



Continue to Step 2
FOR TYPE C - Step 1

Continue to Step 2
Step 2 - Press and hold both buttons for 5 seconds or              until LED begins to flash.
Step 3 - When LED flashes, release both buttons
Step 4 - Press the button you wish to operate the
             opener (your choice).

For type A & B, proceed to step 6.
For type C, continue on to Step 5
Step 5 A. Press and release the Smart-Learn button. B. Press and hold button selected in Step 4 for 3 seconds
 
Step 6 - Programming is complete, to test, press the button selected to
               activate garage door.
 
SECTION II - Stanley, Multi-Code, Linear, Moore-O-Matic
  • Determine specific brand.
  • Set brand mode switches on clicker remote.
  • Open existing remote to expose code switches.
  • Program clicker remote push button
     
Step 1
STANLEY OFF OFF OFF OFF
MULTI-CODE ON OFF OFF OFF
LINEAR/MOORE-O-MATIC OFF ON OFF OFF

Stanley, Multi-Code, Linear, Moore-O-Matic Replacement Transmitter CLT-1, Clicker Brand
 
Step 2
 		Step 3 - Press and hold
             both buttons for
             5 seconds or
             until LED begins
             to flash.

Step 4 - When LED flashes, release both
             buttons.

Step 5 - Press the button you wish to
             operate the opener (your choice).

Step 6 - Programming is complete, to
             test, press the button selected to
             activate garage door.
SECTION III - Genie - 9 Code Switch, Genie - 12 Code Switch

 
  • Open existing remote, determine if there are 9 or 12 code switch settings
  • Set brand mode switches on clicker remote.
  • Program clicker remote push button
     
 
Step 1
GENIE 9 SWITCH OFF OFF ON OFF
GENIE 12 SWITCH ON OFF ON OFF

Genie - 9 Code Switch, Genie - 12 Code Switch Replacement Transmitter CLT-1, Clicker Brand
 
Step 2
 		Step 3 - Press and hold
             both buttons for
             5 seconds or
             until LED begins
             to flash.

Step 4 - When LED flashes, release both
             buttons.

Step 5 - Press the button you wish to
             operate the opener (your choice).

Step 6 - Programming is complete, to
             test, press the button selected to
             activate garage door.
 
 

             
 
SECTION II - Stanley, Multi-Code, Linear, Moore-O-Matic
  • Determine specific brand.
  • Set brand mode switches on clicker remote.
  • Open existing remote to expose code switches.
  • Program clicker remote push button
     
Step 1
STANLEY OFF OFF OFF OFF
MULTI-CODE ON OFF OFF OFF
LINEAR/MOORE-O-MATIC OFF ON OFF OFF

Stanley, Multi-Code, Linear, Moore-O-Matic Replacement Transmitter CLT-1, Clicker Brand
 
Step 2
 		Step 3 - Press and hold
             both buttons for
             5 seconds or
             until LED begins
             to flash.

Step 4 - When LED flashes, release both
             buttons.

Step 5 - Press the button you wish to
             operate the opener (your choice).

Step 6 - Programming is complete, to
             test, press the button selected to
             activate garage door.
   
SECTION III - Genie - 9 Code Switch, Genie - 12 Code Switch

 
  • Open existing remote, determine if there are 9 or 12 code switch settings
  • Set brand mode switches on clicker remote.
  • Program clicker remote push button
     
 
Step 1
GENIE 9 SWITCH OFF OFF ON OFF
GENIE 12 SWITCH ON OFF ON OFF

Genie - 9 Code Switch, Genie - 12 Code Switch Replacement Transmitter CLT-1, Clicker Brand
 
Step 2
 		Step 3 - Press and hold
             both buttons for
             5 seconds or
             until LED begins
             to flash.

Step 4 - When LED flashes, release both
             buttons.

Step 5 - Press the button you wish to
             operate the opener (your choice).

Step 6 - Programming is complete, to
             test, press the button selected to
             activate garage door.

Return to Main Menu